Pass Cisco 300-510 PDF Dumps | Recently Updated 291 Questions
Updated Test Engine to Practice 300-510 Dumps & Practice Exam
Passing the Cisco 300-510 certification exam is a great way for IT professionals to demonstrate their expertise in implementing advanced routing solutions in a service provider network environment. Implementing Cisco Service Provider Advanced Routing Solutions certification can help individuals advance their careers in the IT industry and can open up new job opportunities. In addition, it can help organizations ensure that their IT staff has the necessary knowledge and skills to implement advanced routing solutions in their service provider networks.
NEW QUESTION # 131
An engineer warns to map a multicast IP address to a multicast MAC.
How many bits are used to make the conversion?
- A. high-order 24 bits
- B. lower-order 24 bits
- C. low order 23 bits
- D. higher-order 23 bits
Answer: C
NEW QUESTION # 132
Refer to the exhibit. A network operator is working to deploy a Unified BGP design and allow it to be available only in selected markets and services in the future. The label allocation is not functioning as desired. Which action will fix the issue?
- A. Remove the route policy and only configure "allocate-label".
- B. Remove the allocate-labels command.
- C. Reconfigure the route-policy ALL_LABELS to pass.
- D. Reconfigure the route-policy ALL_LABELS to match all after the drop.
Answer: C
NEW QUESTION # 133
Refer to the exhibit. CE1 and CE2 are iBGP neighbors in AS 65516. All traffic that exits AS 65516 must use the link from CE1 to PE1. CE1 is advertising a higher local preference to CE2, but traffic from CE2 still prefers the PE2 link. Which action corrects the problem?
- A. Configure CE1 to send routes to CE2 with a higher MED.
- B. Add the lower local-preference value on PE2 towards CE2.
- C. Configure CE1 to send routes to CE2 with a higher weight.
- D. Add the next-hop self command to the CE1 neighbor statement for CE2.
Answer: B
Explanation:
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
NEW QUESTION # 134
Refer to the exhibit. While configuring router 2 with all the default values, a network engineer cannot see any route received in router 1. How should the engineer solve the issue?
- A. Set up a priority different than 0 in the interface.
- B. Modify the router ID to be the interface IP on the serial.
- C. Modify the IP address or mask of the interface to a valid one.
- D. Set the network type in S1/0 to point-to-point.
Answer: C
NEW QUESTION # 135
Drag and drop the attributes for the BGP route selection on the left into the correct order on the right. Not all options are used.
Answer:
Explanation:
NEW QUESTION # 136
Refer to the exhibit.
Which task must you perform on interface g1/0/0 to complete the SSM implementation?
- A. configure IGMPv3
- B. disable IGMP
- C. configure OSPFv3
- D. enable CDP
Answer: A
NEW QUESTION # 137
Refer to the exhibit.
The extension header of the IPv6 header is ignored when which value is equal to zero?
- A. Segments Left
- B. Routing Type
- C. Hdr Ext Len
- D. Next Header
Answer: D
NEW QUESTION # 138
Refer to the exhibit.
Refer to the exhibit While troubleshooting a networking issue an engineer identified a suboptimal communication issue on route reflector RR2 In the current environment Router A is a non-route-reflector client for RR1 and RR2 Routers D and E are directly connected iBGP peers.
Router F is not an iBGP peer of routers D and E
Which action resolves the issue?
- A. Enable next-hop-self for BGP peering on router D.
- B. Disable BGP Client-to-Client reflection on router RR2.
- C. Enable next-hop-self for BGP peering on router C.
- D. Remove the route-reflector configuration on router RR2.
Answer: C
NEW QUESTION # 139 
Refer to the exhibit. An engineering team implemented IS-IS on the network, with several different areas.
Recently, router R6 in area 3 has been experiencing excessive CPU usage. To reduce the load, a network engineer implemented route summarization on R2 However. R6 is still receiving the full routes from all routers. Which action must the engineer take to resolve the excessive CPU usage?
- A. Configure router R1 to send only the default route to R2 and R4.
- B. Configure the Level 2 router R6 to manage summarization for the network
- C. Configure all routers as Level 1/2 routers so that route summarization functions throughout the network
- D. Configure routers R3 and R5 to send summary routes to R6.
Answer: D
NEW QUESTION # 140
Refer to the exhibit.
Refer to the exhibit. Network connectivity between bank A and bank B has been lost Users at bank A and bank B are able to successfully reach their directly connected PE routers. All routers in OSPF area 0 are correctly advertising and learning routing updates. Which action resolves the issue?
- A. Configure router PI to advertise the IP prefix of PEI.
- B. Enable next-hop-self under the iBGP peering configuration on routers PEI and PE2
- C. Configure MPLS with an end-to-end label-switched path on each router.
- D. Configure the P routers to redtstnbute BGP routes within OSPF area 0.
Answer: C
NEW QUESTION # 141
Refer to the exhibit.
The extension header of the IPv6 header is ignored when which value is equal to zero?
- A. Segments Left
- B. Routing Type
- C. Hdr Ext Len
- D. Next Header
Answer: D
NEW QUESTION # 142
Refer to the exhibit.
An engineer is troubleshooting an OSPF issue. Router 1 has a neighbor relationship with router 2. Only router 1 classful EIGRP routes can be seen on router 2. In order for all EIGRP routes to be redistributed correctly, which action should be taken?
- A. Router 1 must have the keyword ospf-metric included in the redistribution command for all EIGRP routes to be redistributed.
- B. Router 1 must have the keyword subnets included in the redistribution command for all EIGRP routes to be redistributed.
- C. Router 1 must remove the AS number 1 from the redistribution command for all EIGRP routes to be redistributed.
- D. Router 1 must have the keyword metric-type 1 included in the redistribution command for all EIGRP routes to be redistributed.
Answer: B
NEW QUESTION # 143
Refer to the exhibit. When implementing SRv6, which SID does R2 propagate into area 0 for the prefix 2001:DB8:1:1/128?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 144
Refer to the exhibit.
A customer reports that Host-1 is failing to receive streaming traffic from the IPTV source. The engineer has confirmed that hosts on router R2 are receiving traffic normally and that Host-1 is correctly sending subscription messages to join the IPTV stream. Which action must the engineer take to correct the problem?
- A. Configure IP PIM SSM and IGMP version 2 under interface GigatxtEthernet 1/0/1 on R3
- B. Configure IGMP version 3 under interface GigabitEthernet 1/(V1 on R3
- C. Remove IP PIM SSM and IGMP from interface GigaEthernet 1/0/1 on R3 and configure under global configuration
- D. Remove IP PIM SSM from the global configuration on R3 and configure it under the GigabitEthernet 1/0/1 interface
Answer: B
NEW QUESTION # 145
Refer to the exhibit.
Refer to the exhibit. A network engineer configured three new PE routers to expand the network. The new routers run in the IS-IS routing protocol and reside in the data center in the same exchange as the existing routers. However, the network is now experiencing suboptimal routing. The Layer 2 configuration and VLANs are configured correctly to provide segregation between networks, but the Level 1 routes are not being converted to Level 2 routes. Which action resolves the issue?
- A. On Router 2. summarize internal routes between areas.
- B. On Router 2, redistribute the routes into IGP.
- C. On Router 1, summarize internal routes between areas.
- D. On Router 1, redistribute the routes into IGP.
Answer: A
NEW QUESTION # 146
Refer to the exhibit. A network operator is getting the route for 10.11.11 0/24 from two upstream providers on #XR3.
The network operator must configure #XR3 to force the 10.11.11.0/24 prefix to route via next hop of 10.0.0.9 as primary when available.
Which of these can the operator use the routing policy language for, to enforce this traffic forwarding path?
- A. lower local preference on the prefix coming from 192.168.0.2
- B. weight of 100 on the prefix coming from 192.168.0.1
- C. weight of 0 on the prefix coming from 192.168.0.2
- D. higher local preference on the prefix coming from 192.168.0.1
Answer: D
NEW QUESTION # 147
......
Cisco 300-510 Dumps Cover Real Exam Questions: https://examtorrent.dumpsactual.com/300-510-actualtests-dumps.html
